Three Tigers

Since I had a long night at work and the day will not be less today, I've only worked a little bit on Tiger.

So I am now just been added to shorten the drive shafts to length and hard to solder with the output gear.

For this purpose I first checked with the on-axis position where the gear is soldered and then roughened with a belt sander.





So that the solder is a good connection between the axle and gear I had to hone a few notches in the gear.



So I could then hard-soldering.



Now one must still turn on the solder joints and make everything clean with a rubber polishing wheel.



I even brush your teeth with a small stainless steel brush. So they are not damaged and still all coverings removed from soldering.

Today there is still a first test drive of the tub, but before I have to put the gear ready.

After I've soldered the second drive axle, both annealed and cleaned it comes to installation. The case I fill again completely imt on graphite grease.



Then, the lid must be screwed.



The chain wheels are adapted to a bit of the lathe.





So then they fit exactly over the counter.



And the chain track fits perfectly.



Yet set the suspension at the jacked-tub. The best way to choose if you match strips inserted under the wheels so that they rest at just the right height to adjust the individual rollers. You can say that at least make adjustment in the Bassis.



The chains still mounted. regulator and soldered and programmed for the first test drive.







And of course again a little video of the first ride outdoors.

By the holiday and all the work in my local I have not managed to post it yesterday, the further progress of construction, .... then just now ...

Yesterday my daughter has built a little further on Tiger ..... (under my guidance)

First, we have built the attachment of the upper hull. At the front and inside of the front slope, it has adhered to a connector made ​​of plastic.



Thus, the structure is kept secure and can forward backward Dodge in collisions with obstacles before major damage occurs.



At the back we have again built a bracket with two magnets. Which can be solved with blows from the front, the upper part has nevertheless firmly in the driving mode and the opening and closing a breeze.







It continues with the speaker. Base and lid are already available, but must still be adjusted slightly.



And so this is also formed slowly. It just takes a little longer if you have never done it, but that does not matter. This is the first Tiger to the woman also helped build .....

Enchanted!!   
As electronics sound what do you use? Benedini?
  

Hi Gertig,

for the sound and multiple functions I use the sound module of Beier.

regards Edwin

  Hi edwi n bellissimi e interessanti , anche da studiare i nw progressi sul Tiger con l'alloggiamento della cassa acustica e le up sui riduttori , ce' sempre da imparare .... saluti robby62 e riky94 ...  

The third tiger it goes with the internals on. Now is the turn of the electronics.

I build again the plastic together and place the battery divided on both sides.









Then I have already begun to connect Beier sound module.



After I had unpacked the transmitter I have read through the manual myself first, since I have not had this and was nowhere to be found in the manual, the polarity of the receiver. It was only when I looked at the label of the receiver exactly could I find the remnants of the markings as the connectors are plugged in properly after an hour. And so it goes further up next time.

The third tiger is slowly finished this week in any case.

Here I have the main wiring harness of the tank ......



And by the way, I am still in the last two days for car and transmitter employs coordinated. This is somewhat difficult since these channels do not offer those options usually used by me, but now he goes ....

The wiring is done slowly.

Even the LED's provided by the headlamp and the MG with a matching resistance and solder it to the connector.





The connections to the module Beier not forget.



And a little clean up in the hull.



Then the tower of the series, the first obstacles as I can.



Since I still have begun to build the cradle with the power requirements. Tomorrow will be finished so the technique.

  soluzione tecnicamente bella e interessante edwin , quella adottata da inserire nella Torretta del Tiger , gran bel lavoretto .......... saluti robby62:cia: