Three Tigers

Hello Edwin,
the magnets for the closure of the hull have a better grip of the screws, I have already used myself and are an excellent solution!   
Thank you for all the work modeling.

 

Yesterday I was on the model tag in military technology museum in Röthenbach.

Since I have the same but also made ​​a short film of the first tiger.



At the sound but again what do I do, I still do not like the.

Very realistic in the movement, I like!   

 

Now I'm doing as far as the Tigers finished second. If I still get the outstanding sound module, the first two Tigers on Sunday are ready for collection.

But first I have to break down and eviscerate the tower.



Then I made an extension of the cradle of an aluminum bracket and bolted to this.



When I run on the aluminum brackets still purchase a plastic layer bonded to the I was able to mount the servos for the recoil and elevation.









The button for the speed camera I'm building now getting yourself This is not as sensitive as the bought and better adjusted by simply bending the spring steel something.



By the way, so I do not lose the plug I have this still soldered to the regulators.



Next up was the speaker. Bottom and top I had previously gone through.



After gluing and sanding this also fits the same inlet into the tub.

It goes on.

The speaker, of course, gets back their insulation and because I was just I have the same Eeny for the third Tigers cut.



Trimming the electronics and battery box is now a simple exercise.





To control the motor tower I use a micro controller that requires no separate connection to the battery and fits perfectly to the HL-tower drives.



It's just a little difficult to solder the cable to it.



and of course the LEDs get their matching resistors to the battery.



The holder of the upper hull I'm back with magnets and screws twisted plan.







and at the end of today I have as far as it was possible the transmitter programming and installation of the sound module prepared.
If the tiger is still coming tomorrow because even done yet.

Hello Edwin,
behind all these seemingly simple things there is a careful study for the internal arrangement of the components with a well-balanced weight distribution.
Looking at your work is much to learn.  
It seems superfluous now get so many compliments ......   

Hi Gertig.

Thank you for the compliment...... 

and you have recognized it. I have an aversion to an incorrect weight distribution, since this greatly affects the performance even in tanks.

regards Edwin

Tiger is now the third but made ​​ready.

Today I first mounted the rollers and idlers and set the track this.





Next was the adjustment of the upper hull of the series. This again seems to come from a new form. I had to practically nothing even though I will always be ewas excess.



The front must be doubled at the inside a little.



So now you can customize with a little spackle the Sater.



To install the transom with non-fixed I glue the sides with tape. Since no glue holding it and I get the part back from the resulting bracket.



So I can now glue the sides and then the bottom end.





This must now first again harden overnight and tomorrow we continue with the tub.

And on it goes.

After I glued the plastic plates yet processed the rear now looks like this.



By the way I again drilled new housing for the countershaft and milled. In this I have to cut each 15 times an M1, 2 thread again.

This works best when used for tapping a good cooling lubricant emulsion. This I fill out the blind holes using a syringe.



If one cuts the threads in the filled holes, the liquid is forced out of the taps and rinsed with the chips. So the tap stuck not so easy.



Then the gear assembly could begin in the tub and it must take time.



So I have properly aligned with each other and now the gearbox bolted to the counter and sealed enclosures.

  ciao edwin , gran bei progressi ci mostri coi tuoi lavori sul Tiger compresa la parte dello scafo e dei motori con riduttori .... ammirevoli come d'altronde siamo abituati a vedere sui tuoi progetti , saluti e buona domenica robby62 e riky94 ....