First, just as a test if I succeed

Membro X Messaggi : 356 Data d'iscrizione : 14.05.13

By the way, I'm just going to mill aluminum, a master and this time in a slightly larger scale of 1/6

If I succeed here is a joint report produced construction, first for a drive bassis which should surpass the previous ways the behavior of the suspension and the drive clearly and can then later be built in many variants.

But first I need the one I cut from a block of aluminum alloy shaft corresponding to the band saw.

First, just as a test if I succeed 15834008yf

First, just as a test if I succeed 15834008yf

Outside it is getting so 66.66 x 28.81 x 24.41 mm, but at a cutting of about 85% if I succeed.

First, just as a test if I succeed 15834009fn

First, just as a test if I succeed 15834010jt

Next, I position the component using an edge finder to two holes to really precisely set.

First, just as a test if I succeed 15948991ty

After I hit the right coordinates, and have a little pre-drilled so that the gun drill obtained its leadership, I drill two 3mm holes absolutely parralelle the 66 mm deep through the block. The canon is to drill absolutely necessary as a normal drill at this depth estimated at 2 mm above this level.

First, just as a test if I succeed 15948988rh

First, just as a test if I succeed 15948988rh

First, just as a test if I succeed 15948989sc

First, just as a test if I succeed 15948990wb

I then milled the top of the first level and then do a round with 6mm radius.

First, just as a test if I succeed 15948992fr

With a 6mm router will talk to one side of the segments milled.

First, just as a test if I succeed 15948993bq

First, just as a test if I succeed 15948994zw

I work as the bottom, but leave in the middle of the guide bar are blank.

First, just as a test if I succeed 15948995az

First, just as a test if I succeed 15948996ur

As far as times to the present.

_________________
http://apamotec.de.tl/Home.htm

Ospite

Hello Edwin,
I did not understand what you're doing?
It 'a piece for a model in 1:6 scale?

Question

First, just as a test if I succeed 4190927916

Membro X Messaggi : 356 Data d'iscrizione : 14.05.13

Hi Gertig,

I'm trying here a master link to a Panzer III drive in 1/6 scale to build, I can then use for making molds.

regards Edwin

_________________
http://apamotec.de.tl/Home.htm

Ospite

ok you're doing a master for a mold of a piece of the panzer III in 1:6 scale.
This means that even works on 1:6 scale tank?

First, just as a test if I succeed 4190927916

Membro X Messaggi : 356 Data d'iscrizione : 14.05.13

Yes, if I succeed in a chain with the help of this master to make a friend and I build a Panzer III hull in 1/6 scale as Bassist for different setups.

_________________
http://apamotec.de.tl/Home.htm

Membro X Messaggi : 356 Data d'iscrizione : 14.05.13

On the chain link today I occupied myself with the cutouts. This takes time, as the members are indeed a good fit and exactly later.

I milled the day with a 3mm router with abundant use of cooling lubricants.

First, just as a test if I succeed 15980310rd

First, just as a test if I succeed 15980310rd

First, just as a test if I succeed 15980311zw

And so it looks after two hours from then.

First, just as a test if I succeed 15980312yh

First, just as a test if I succeed 15980313bp

_________________
http://apamotec.de.tl/Home.htm

Membro X Messaggi : 356 Data d'iscrizione : 14.05.13

It goes on ....

Today I drilled and milled only the notches on the lateral fins, the difficulty was that these are arranged inclined to the member.

after I had determined that of Issues on the drawing I could hit the 4 holes with the coordinate table and drill the ends of which a 2.9 mm hole.

First, just as a test if I succeed 15989106yo

First, just as a test if I succeed 15989106yo

First, just as a test if I succeed 15989107ad

After I determined the exact location and extent of the cutouts with the holes I could clamp the blank corresponding to a straight line between the holes and carefully milled out with a 2mm diamond cutter.

First, just as a test if I succeed 15989108hk

First, just as a test if I succeed 15989108hk

After I have the whole then even prepared the rough with a file, it now looks like this. The real finishing takes place only when all milling operations are completed, but it will take some time. That was what you see here today again 2.5 hours work.

First, just as a test if I succeed 15989109if

First, just as a test if I succeed 15989109if

First, just as a test if I succeed 15989110ek

_________________
http://apamotec.de.tl/Home.htm

Membro X Messaggi : 1321 Data d'iscrizione : 09.04.11

_________________
RCTANKIR siamo solo noi!!! First, just as a test if I succeed 1911839571

Membro X Messaggi : 356 Data d'iscrizione : 14.05.13

And it goes back a little bit further.

To be able to mill out and file the openings in the chain link clean I drill the corners as a boundary with a 1.5 mm drill. The positions of the holes do I find out my CAD drawing again, and then they go on to coordinate table.
But first I must find the zero point of two axes with an edge finder.

First, just as a test if I succeed 16026171pe

First, just as a test if I succeed 16026171pe

So I can now drill the first two lateral openings of the bottom of the chain link.

First, just as a test if I succeed 16026172uk

For drilling the middle breakthrough I turn around the limb, there is in this way in the guide bar and the breakthrough is right below this.

First, just as a test if I succeed 16026174gh

First, just as a test if I succeed 16026174gh

To see all the holes now out of the top.

First, just as a test if I succeed 16026173yf

Since I still have a little time I milled the first breakthrough times already grossly out with the diamond cutter. The work I'm doing fine then later with a file.

First, just as a test if I succeed 16026175is

First, just as a test if I succeed 16026175is

So you also get a little insight about how expensive something is ...... today I have used for about 2.5 hours.

_________________
http://apamotec.de.tl/Home.htm

Membro X Messaggi : 356 Data d'iscrizione : 14.05.13

Today it was again about 2.5 hours which have brought me a little further.

First I milled the second breakthrough coarse.

First, just as a test if I succeed 16036174rl

First, just as a test if I succeed 16036174rl

The next step was the finer milling of breakthroughs in the series, which the first part is the actual contours. And I've missed me but at a level which is not bad anyway, I still have to trim with wood filler in some places, so you can not mill and file the chain link.

First, just as a test if I succeed 16036175qu

First, just as a test if I succeed 16036175qu

First, just as a test if I succeed 16036176xr

The guide bar must of course also be edited and so gets its slopes.

First, just as a test if I succeed 16036177lz

Since this is also broken through relatively complicated and I can not mill it directly I drill 3 holes in first.

First, just as a test if I succeed 16036178hl

First, just as a test if I succeed 16036178hl

Then I fräses into a breakthrough from the top to the guide bar.

First, just as a test if I succeed 16036179eo

The gross irregularities I file ever from the guide bar. The work I'm doing fine only if all milling operations are completed so far.

First, just as a test if I succeed 16036180vn

First, just as a test if I succeed 16036180vn

_________________
http://apamotec.de.tl/Home.htm

» Test Leopard 2a6 Tamiya VS Tiger I Tamiya