Titolo: Re: A Panzer IV tank made of aluminum and is formed with brushless motor Mar 30 Lug 2013, 18:07
Today I was able to make and glue only the supports of the transmission. That must be hard at first before I can put this.
_________________ http://apamotec.de.tl/Home.htm
robby62 Membro X
Messaggi : 5000 Data d'iscrizione : 26.02.11
Titolo: Re: A Panzer IV tank made of aluminum and is formed with brushless motor Mar 30 Lug 2013, 23:50
............. ..................................... ammirevole anche nei dettagli ...... robby62 .......
_________________ RCTANKIR siamo solo noi!!!
Edwin-Apamotec Membro X
Messaggi : 356 Data d'iscrizione : 14.05.13
Titolo: Re: A Panzer IV tank made of aluminum and is formed with brushless motor Mer 31 Lug 2013, 15:58
Hi robby,
thank you for your comment.....
regards Edwin
_________________ http://apamotec.de.tl/Home.htm
Edwin-Apamotec Membro X
Messaggi : 356 Data d'iscrizione : 14.05.13
Titolo: Re: A Panzer IV tank made of aluminum and is formed with brushless motor Gio 01 Ago 2013, 16:58
So, now was the gearbox fitted to the series.
First there was the tub with the large standard motors turn. Need so that they fit into the bath but all the gear back to the exterior walls and the axes need to be shortened.
the attachment of the gear I can reduce my assembly by way of one, easily accessible screw each gear. So I had to choose only the points for drilling, boring and cut the thread.
img]http://up.picr.de/15363273ln.jpg[/img]
But now I had to shorten the shaft clearly as you can see here.
For this, the support bearing is now sitting quite outside.
After fitting the chains as far as the tub is then finished and can be her new owner.
In the second pan with the brushless motor I have the same time also set the gear all the way to the outside and cut the axes. The flattening of the axes had to be prolonged in all gears, of course. The easiest way is by being careful abfeilt.
Here again the fastening of a transmission with only one screw and then the whole pan with chains
Wed of brushless pan I also made another test drive because the controller settings.
The suspension works in the context of the possible suspension travel now quite well. Your owner will first have to stick together all the roles well. I did the same at the beginning of the test drive lost half of the rollers.
But this tub is not yet clear. In it, I will test new engines with flywheels and if they are good to their owners must also equal delighted ...
_________________ http://apamotec.de.tl/Home.htm
robby62 Membro X
Messaggi : 5000 Data d'iscrizione : 26.02.11
Titolo: Re: A Panzer IV tank made of aluminum and is formed with brushless motor Ven 02 Ago 2013, 14:39
la vista laterale dello scafo e' splendida e di una pulizia di linne ammirevole tanto da risultare ancor piu' realistico il movimento dello scafo nel filmato che ci proponi , saluti e buona giornata da robby62 e riky94
_________________ RCTANKIR siamo solo noi!!!
Edwin-Apamotec Membro X
Messaggi : 356 Data d'iscrizione : 14.05.13
Titolo: Re: A Panzer IV tank made of aluminum and is formed with brushless motor Ven 02 Ago 2013, 16:33
As I wrote yesterday, I still got the new brushless motors are also suitable for mounting rotating masses on this gear and then today I have tested and installed.
First I cut off but two steel washers for flywheels with the band saw and the engines to be installed in the transmission rebuilt.
The steel discs, I then put on the lathe to shape and drilled the mounts.
And so then I was able to install everything in the gearbox. Further adjustments were not necessary to pan and transmission.
After I had finished the drive an extensive test drive was of course necessary and I am satisfied.
Now both tanks can be sent to your owners and maybe then dip it in a building report so again.
_________________ http://apamotec.de.tl/Home.htm
Contenuto sponsorizzato
Titolo: Re: A Panzer IV tank made of aluminum and is formed with brushless motor
A Panzer IV tank made of aluminum and is formed with brushless motor